Bently Nevada 330710-000-060-10-02-00 3300 XL 11 mm Proximity Probe

Product Introduction

The Bently Nevada 330710-000-060-10-02-00 is a 3300 XL 11 mm proximity probe designed for accurate, non-contact vibration and position measurements in critical rotating machinery. Manufactured in the U.S.A., this probe features a rugged AISI 304 stainless steel case, a PPS tip, and an integral armored cable for enhanced durability in harsh industrial environments. The model number 330710-000-060-10-02-00 specifies a 0 mm unthreaded length, 60 mm overall case length, 1.0 meter total cable length, miniature coaxial ClickLoc connector, and no agency approval.

Technical Parameters

• Probe Type: 3300 XL 11 mm Proximity Probe
• Thread Size: M16 x 1.5
• Unthreaded Length: 0 mm
• Overall Case Length: 60 mm
• Total Length: 1.0 meter (3.3 feet)
• Connector: Miniature coaxial ClickLoc connector, standard cable
• Probe DC Resistance: 5.9 ± 0.5 ohms (center to outer conductor)
• Probe Tip Material: Polyphenylene sulfide (PPS)
• Probe Case Material: AISI 304 stainless steel
• Cable Specification: 75 Ω triaxial, FEP insulated
• Probe Case Torque: 63.3 N•m (560 in•lb) for M16x1.5
• Connector-to-connector torque: Finger tight (max 0.565 N•m)
• Minimum Bend Radius: 25.4 mm (1.0 in) with or without armor
• Operating/Storage Temperature: -52°C to +177°C (-62°F to +351°F)

Parameter Analysis

The 330710-000-060-10-02-00 offers a 1.0 meter total length, ideal for installations where the probe is mounted close to the monitor. The 60 mm overall case length provides adequate thread engagement for standard mounting. The M16x1.5 thread ensures compatibility with common mounting hardware. The miniature coaxial ClickLoc connector allows quick and secure cable attachment. The probe’s DC resistance of 5.9 ± 0.5 ohms ensures consistent signal transmission.

Application Scenarios

This probe is widely used for vibration and position monitoring on turbines, compressors, pumps, and other rotating machinery. It is suitable for measuring shaft vibration, axial position, and speed/phase reference. The 11 mm sensor size provides excellent linear range and sensitivity for most industrial applications.

Installation Guide

• Mount the probe using the M16x1.5 thread. Ensure the thread engagement does not exceed 24 mm.
• Apply the recommended torque of 63.3 N•m (560 in•lb) to the probe case.
• Connect the cable using the ClickLoc connector; tighten finger tight, do not exceed 0.565 N•m (5 in•lb).
• Maintain a minimum bend radius of 25.4 mm (1.0 in) for the cable.
• For optimal performance, use a flat target surface of at least 30.5 mm diameter or a shaft diameter of at least 152 mm.

Compatibility

The 330710-000-060-10-02-00 is compatible with Bently Nevada 3300 XL series monitors and proximity systems. It works with standard 3300 XL extension cables and proximitors. The ClickLoc connector ensures secure mating with compatible cables.

Maintenance Advice

• Periodically inspect the probe tip and cable for damage.
• Keep the probe tip clean and free of debris.
• Avoid exposing the probe to temperatures below -34°C (-30°F) as this may cause premature failure of the pressure seal.
• Check connector tightness periodically; do not overtighten.

Procurement Advice

When ordering, verify the model number 330710-000-060-10-02-00 to ensure you receive the correct configuration. Consider your required cable length and connector type. For applications requiring agency approvals, select the appropriate option. Contact TenBN for availability and lead times.

FAQ

What is the temperature range of this probe?

The operating and storage temperature range is -52°C to +177°C (-62°F to +351°F). However, exposure below -34°C may damage the pressure seal.

What is the recommended target size?

For flat surfaces, the minimum recommended diameter is 30.5 mm (1.2 in). For shafts, the minimum recommended diameter is 152 mm (6.0 in).

What is the probe DC resistance?

The DC resistance from center conductor to outer conductor is 5.9 ± 0.5 ohms for a 1.0 meter probe.

Can this probe be used with armored cable?

Yes, this model includes armor. The minimum bend radius is 25.4 mm (1.0 in) with or without armor.

What is the thread size?

The probe case thread is M16x1.5. Maximum thread engagement is 24 mm.