Bently Nevada 32000-16-05-00-080-03-02 31000 Proximity Probe Housings

Product Introduction

The Bently Nevada 32000-16-05-00-080-03-02 is a probe housing assembly (31000 Proximity Probe Housings), engineered for continuous protection of rotating machinery. TenBN supplies this genuine Bently Nevada component with full documentation and ready stock for plants running condition monitoring programs on critical equipment.

Technical Parameters

• Model: 32000-16-05-00-080-03-02
• Product Type: 31000 Proximity Probe Housings
• Product Series: 31000 / 32000
• Origin: U.S.A Probe Option
• Probe Option: With Connector : 16 3300 XL 8 mm probe
• Probe cable length Option: 05 0.5 m (20 in)
• Standoff adapter Option: 00= 00 mm
• Probe penetration Option: 080 =80 mm
• Fittings Option: :
• Mounting thread Option: 02 3/4-14 NPT (Required if ordering Standoff Adapter Option.)
• Housing Material: Glass-reinforced Polyphenylene Sulfide (PPS) thermoplastic containing conductive fibers
• Sleeve Material and Retaining Chain: AISI 304 stainless steel
• Outer Sleeve and Exterior Screws: AISI 303 stainless steel
• O-Ring Material: Neoprene®

Parameter Analysis

The ordering string of the 32000-16-05-00-080-03-02 encodes its physical and electrical configuration, so every digit should be checked against the machine drawing before substitution. The probe Option specifies with Connector : 16 3300 XL 8 mm probe. The probe cable length Option specifies 05 0.5 m (20 in). The standoff adapter Option specifies 00= 00 mm. The unit is rated for operation from -51°C to +105°C (-60°F to +221°F).

The housing assembly seals the probe penetration against wash-down and dust while allowing standard probe maintenance, combining mechanical protection with the electrical performance of the enclosed probe.

Application Scenarios

Installations on rotating machinery that demand sealed probe penetrations rely on this housing to guard against dust, hose-directed water, and mechanical contact while keeping the probe serviceable.

Installation Guide

Confirm every option digit against the machine drawing, mount the housing through its threaded connection, tighten the retaining nut to the documented torque, and keep the sleeve O-rings seated to preserve the environmental seal. Set the probe gap after assembly and verify before start-up.

Compatibility

This component belongs to the 3300 XL 8 mm proximity system and is engineered to work with the associated probes, extension cables, Proximitors, and monitoring hardware of the same system. Bently Nevada components sharing the same part number are fully interchangeable, so a stocked spare can be fitted without re-engineering the measurement loop. TenBN can supply the complete chain under consistent part numbers.

Maintenance Advice

Inspect the housing cover, screws, and O-rings at each maintenance opportunity, and confirm the retaining nut torque has not relaxed in service. Keep the unit within its -51°C to +105°C (-60°F to +221°F) operating envelope in service and storage.

Procurement Advice

Confirm the complete part number against your machine’s bill of materials before ordering, since each option digit changes the mechanical or electrical fit. TenBN stocks genuine Bently Nevada components and provides the official service documentation for this model. For inventory, pricing, and lead time on the 32000-16-05-00-080-03-02, contact [email protected].

Frequently Asked Questions

What is the operating temperature range?

The unit is rated from -51°C to +105°C (-60°F to +221°F), covering the temperature extremes typical of turbomachinery installations.

Can this spare be interchanged with existing components?

Bently Nevada components sharing the same part number are fully interchangeable, so this spare can replace an existing unit without recalibrating the loop when the complete part number matches.

How do I confirm the right part number?

Check every option digit against the machine bill of materials, then contact [email protected] with the full string; the TenBN team will confirm fit, stock, and documentation.