Bently Nevada 21000-16-10-15-092-03-02 Proximity Probe Housing

Product Introduction

The Bently Nevada 21000-16-10-15-092-03-02 is a probe housing assembly (4 enclosures and are), engineered for continuous protection of rotating machinery. TenBN supplies this genuine Bently Nevada component with full documentation and ready stock for plants running condition monitoring programs on critical equipment.

Technical Parameters

• Model: 21000-16-10-15-092-03-02
• Product Type: 4 enclosures and are
• Product Series: 21000 / 24701
• Product Number: 21000-16-10-15-092-03-02
• Probe Option: with Connector: 16 3300 XL 8 mm probe
• Probe cable length Option: 10 1.0 m (39 in)
• Standoff Adapter: 1.5 in (38 mm) = 15
• Probe penetration ( Option: D Dimension)：092=9.2in
• Fittings: -03 One 3/4-14 NPT plug
• Will default to 02 Option: if C: Option Standoff Adapter Length
• L a probe sleeve of Option: al length
• L an Option: al standoff adapter

Parameter Analysis

The ordering string of the 21000-16-10-15-092-03-02 encodes its physical and electrical configuration, so every digit should be checked against the machine drawing before substitution. The probe Option specifies with Connector: 16 3300 XL 8 mm probe. The probe cable length Option specifies 10 1.0 m (39 in). The probe penetration ( Option specifies d Dimension)：092=9.2in. The unit is rated for operation from -50 °C to +40 °C.

The housing assembly seals the probe penetration against wash-down and dust while allowing standard probe maintenance, combining mechanical protection with the electrical performance of the enclosed probe.

Application Scenarios

This housing assembly protects the proximity probe where it passes through the machine casing on turbines, compressors, and pumps. It is well suited to wash-down areas, outdoor installations, and hazardous locations where the probe needs mechanical and environmental protection.

Installation Guide

Confirm every option digit against the machine drawing, mount the housing through its threaded connection, tighten the retaining nut to the documented torque, and keep the sleeve O-rings seated to preserve the environmental seal. Set the probe gap after assembly and verify before start-up.

Compatibility

This component belongs to the 3300 XL 8 mm proximity system and is engineered to work with the associated probes, extension cables, Proximitors, and monitoring hardware of the same system. Bently Nevada components sharing the same part number are fully interchangeable, so a stocked spare can be fitted without re-engineering the measurement loop. TenBN can supply the complete chain under consistent part numbers.

Maintenance Advice

Inspect the housing cover, screws, and O-rings at each maintenance opportunity, and confirm the retaining nut torque has not relaxed in service. Keep the unit within its -50 °C to +40 °C operating envelope in service and storage.

Procurement Advice

This unit is supplied new & original in factory packing with 12 months factory warranty. Confirm the complete part number against your machine’s bill of materials before ordering, since each option digit changes the mechanical or electrical fit. TenBN stocks genuine Bently Nevada components and provides the official service documentation for this model. For inventory, pricing, and lead time on the 21000-16-10-15-092-03-02, contact [email protected].

Frequently Asked Questions

What is the operating temperature range?

The unit is rated from -50 °C to +40 °C, covering the temperature extremes typical of turbomachinery installations.

What connector or interface does it use?

It uses -03 One 3/4-14 NPT plug, matching the standard Bently Nevada measurement chain.

Can this spare be interchanged with existing components?

Bently Nevada components sharing the same part number are fully interchangeable, so this spare can replace an existing unit without recalibrating the loop when the complete part number matches.

How do I confirm the right part number?

Check every option digit against the machine bill of materials, then contact [email protected] with the full string; the TenBN team will confirm fit, stock, and documentation.